Opel Frontera

Since 1992 of release

Repair and car operation

Opel of Frontera
+ Cars of mark Opel Frontera
- Current leaving and service
   The routine maintenance schedule
   Current leaving
   The information on adjustment
   Check of levels of liquids
   Check of a condition of tyres and pressure in them
   Replacement of impellent oil and the oil filter
   Check of level of a liquid of system of hydrostrengthening of a wheel
   Rotation of wheels
   Check of a condition and replacement of hoses of an impellent compartment
   Condition check, adjustment of a tension and replacement приводного a belt (only for engines with tension adjustment)
   Check and adjustment of turns of idling of the engine and level WITH
   Check of a condition of the battery, care it and gymnastics
   Check and replacement of spark plugs
   Check and replacement candle ВВ wires, a cover and бегунка the distributor
   Check of level of oil in a manual box of a gear change and a distributing box
   Check of level of a lubricant liquid of differential of forward and back bridges
   Check of fuel system
   Check of functioning of system of cooling
   Check of a condition of system of release of the fulfilled gases
   Check of a condition of components of a suspension bracket and steering
   Check of a condition of protective covers of power shafts of forward wheels
   Make check of brake system and replacement of a brake liquid with the subsequent prorolling
   Check of a condition and replacement of brushes of screen wipers
   Refuelling of a cooler of system of cooling
   Replacement of the fuel filter
   Replacement трансмиссионного oils РКПП and a distributing box
   Replacement of a lubricant liquid of differential of forward and back bridges
   Replacement of a distributive belt of the engine
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Manual box of a gear change
+ Kardannye shaft, the main transfer
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Controls and operation
+ Electric equipment schemes

Check and replacement candle ВВ wires, a cover and бегунка the distributor

PERFORMANCE ORDER

1. Check of a condition candle ВВ wires should be made regularly through the recommended intervals and each time at replacement of spark plugs.
2. Begin this procedure with external survey of wires at the working engine. In the blacked out garage (track that indoors there was a good ventilation) start the engine and attentively examine each wire. Try not to touch moving parts of the engine. In the presence of breakage the wire will spark in a damage place. In this case replace wires, then allow to the engine to cool down.
3. Disconnect a negative wire of the battery. The prevention The prevention: If the radio receiver of your car is equipped by system of protection against larceny, make sure that you have typed a correct code before a battery detachment.
4. In order to avoid mess at installation check ВВ of wires should be made serially.
5. Disconnect ВВ a wire from a spark plug. Do not pull for a wire, only and a socket.
6. Examine an internal part of a socket on presence of corrosion which looks like a white friable powder. Connect a wire with a socket to a spark plug. The socket should hardly a network on a candle. If it is not possible to reach it, again remove a wire and correct flat-nose pliers position of the plug in a socket.
7. Pure rags wipe wires outside on all length, deleting from them stuck dirt and greasing. After clearing check up a wire on presence of traces прогаров, cracks and other damages. Do not bend a wire under acute angles since it can lead to a conductor regional ohm.
8. Disconnect ВВ a wire from the distributor. Do not forget to pull only for a socket. Check up it on presence of corrosion and connect in the same way, as well as a spark plug wire. If necessary replace a distributor wire.
9. Check up other wires of spark plugs, and after check make sure that each of them is reliably attached to the distributor and a candle.
10. If candle wires demand replacement, buy the set of wires specially intended for your model of the engine. Wires of the necessary length enter into sets and with the established sockets. Remove and replace ВВ wires on one not to admit mess in an operating procedure of cylinders at their installation.
	11a. Ослабьте screws or open clips, then uncover the distributor. Take away a distributor cover so that it was possible to examine it from within.
	11b. Give screws (if they are available) and remove бегунок from a shaft.
	11с. In drawing covers of the distributor some of widespread defects to which it is necessary to pay attention at survey (if there are doubts concerning its condition, replace it is better) are shown.
	11d. Check up a cover and бегунок the distributor on presence of signs of deterioration, cracks, coal traces and the worn out, burnt slightly or weakened contacts. At detection of defects replace a cover or бегунок. Usually a cover and бегунок it is accepted to replace each time at replacement of candle wires. At installation of a new cover on one disconnect ВВ wires from an old cover and connect them to new in precisely same order - never disconnect all wires simultaneously in order to avoid mess in an operating procedure of cylinders at their installation.