Opel of Frontera
+ Cars of mark Opel Frontera
+ Current leaving and service
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Manual box of a gear change
+ Kardannye shaft, the main transfer
+ Brake system
- Suspension bracket and steering
+ Suspension bracket of forward wheels and the forward bridge
+ Suspension bracket of back wheels and the back bridge
- Steering with the hydraulic booster
Verifying and adjusting works on a steering
Works on a steering drive
Steering wheel and steering column
The steering mechanism
The hydraulic booster pump
+ Onboard electric equipment
+ Controls and operation
+ Electric equipment schemes
It is necessary to remind once again that it is not recommended to remove a safety pillow independently. Nevertheless here instructions of the security measures connected with carrying out of this work are resulted:
1. All works with a safety pillow are authorised to be spent in the presence of a certain experience. The mechanic who is not knowing the devices of a pillow of safety, to work is not supposed. The complete set of a pillow of safety includes the management block, a control lamp, a pillow of safety in a steering wheel or a pillow of safety of the forward passenger, contact knot and a plait of cables.
2. Works with a safety pillow are supervised in some countries by the law on explosives.
3. In the presence of a pillow of safety of the forward passenger it is not necessary to establish near to a zone of its action such additional accessories, as for example, fixture for a receiver, the holder of bottles for drinks, cartridges, additional mirrors, etc. The specified elements can prevent at deployment of a pillow of safety.
4. Opening of any elements of considered system is not supposed.
5. Pillow elements are sensitive. If to drop a safety pillow its functioning can be broken.
6. If the car has to be painted, it is necessary to inform a repair truck on presence of a pillow of safety as it is impossible to subject a pillow of safety to temperature influence above 90 ° With.
7. At performance of welding works disconnect a cable of weight from the storage battery. If welding is made near to the management block, it is recommended to remove the management block. In any case it is necessary to disconnect a plait of cables.
At removal and installation, and also at replacement of details of a steering:
| PERFORMANCE ORDER
| 1. Switch off ignition.
| 2. Disconnect a cable of weight from the storage battery and close a negative pole of the battery so that on it any metal subject has not got.
| 3. After switching-off of the storage battery wait minute that the condenser of the block of management could be discharged.
|4. At performance of works with a steering, for example, with a steering wheel, steering draughts, a steering column, etc. a steering establish in average position.
|5. At removal of a steering wheel a steering establish in average position that at the subsequent assemblage to exclude damage of contact knot.
|6. If the safety pillow has worked in an emergency to replacement is subject not only a pillow, but also the management block.
|7. With a safety pillow it is authorised to replace a steering wheel only with other steering wheel resolved to application by firm Opel.
|8. If the safety pillow acts in film, it needs to be put the soft party upwards.
|9. The soft party of a pillow of safety should be wiped only a towel moistened with water, or a cleaner recommended by firm Opel.
|10. Before installation of a pillow of safety it is necessary to check up, whether it is disconnected and whether the storage battery is closed and whether ignition is switched off.
After switching-off of the storage battery certain stores of memory should be again reprogrammed. Thus mean electric стеклоподъемники, hours and the radio receiver coding.
In the description of works resulted more low removal and installation of the parts demanded for removal a steering are specified only.
REMOVAL AND INSTALLATION OF KNOT OF THE PILLOW OF SAFETY
| PERFORMANCE ORDER
| 1. Disconnect a cable of weight from the storage battery and wait one minute. The condenser of the block of management should be discharged.
|2. Turn away four bolts of fastening from outside a steering wheel and take out knot of a pillow of safety. Two bolts from four are shown on an illustration. Others two are on an opposite side. On an illustration the steering wheel is removed.
| 3. Расстыкуйте штекерное connection of knot of a pillow of safety.
The safety pillow in sequence, by return to removal is established.
| PERFORMANCE ORDER
|1. Bolts tighten the moment of 8 Nanometers. Thus at first tighten two bolts on the one hand, and then two bolts with another, that is the sequence corresponding to numbering on an illustration is observed.
REMOVAL AND INSTALLATION OF CONTACT KNOT
| PERFORMANCE ORDER
| 1. Disconnect a cable of weight from the storage battery and wait one minute.
| 2. Remove knot of a pillow of safety as it is described above.
| 3. Remove a steering wheel as it is described above.
|4. Turn away six bolts and remove the bottom cover of the panel of the devices, shown on an illustration.
|5. Turn away six bolts and remove a casing of facing of a steering column.
|6. Расстыкуйте штекерное connection of the combined switch and contact knot.
|7. Turn away four bolts and remove contact knot from a steering column.
|8. At installation contact knot establish precisely in average position. For this purpose turn the coil on a complete revolution clockwise and then on 2.5 turns counter-clockwise so that two marks have coincided. At installation check up, that the steering was on the average position.
|9. Other works are spent to sequences, return to removal. Steering wheel installation is described in separate subsection.
|10. Establish details of a casing of facing of a steering wheel according to an illustration and fix their six bolts.
|11. In summary connect the storage battery. Thus nobody should be in the car.