Opel of Frontera
+ Cars of mark Opel Frontera
+ Current leaving and service
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Manual box of a gear change
+ Kardannye shaft, the main transfer
+ Brake system
- Suspension bracket and steering
+ Suspension bracket of forward wheels and the forward bridge
+ Suspension bracket of back wheels and the back bridge
- Steering with the hydraulic booster
Verifying and adjusting works on a steering
Works on a steering drive
Steering wheel and steering column
The steering mechanism
The hydraulic booster pump
Safety pillow
+ Body
+ Onboard electric equipment
+ Controls and operation
+ Electric equipment schemes
|
The hydraulic booster pump
Here too it is necessary to take into consideration year of release of the car as depending on it works have some differences. Distinction is defined in most cases by type of the established engine.
REMOVAL AND PUMP INSTALLATION
The engine of 2.0 l (C20 NE)
These engines were established to the middle of 1995 of release.
| PERFORMANCE ORDER |
| 1. Remove клиновой a belt of a drive of the pump as it is described more low. |
| 2. Disconnect soaking up hose and the pressure head pipeline from the pump. |
| 3. Collect a following liquid. The hose is fixed by a collar, the pipeline накидной a nut. Joinings are shown on an illustration. |
| 4. Close apertures. |
| 5. Now it is possible to turn away bolts of fastening and to remove the pump from the console. |
6. If it is necessary установ ить the new pump, turn on at once a coupling bolt and remove a rotary plate, since. It is rearranged on the new pump.
|
| 7. Bolts of fastening of a rotary plate tighten the moment of 25 Nanometers. |
| 8. The pump with the console and a coupling bolt is established. Check up клиновой a belt, put on it and adjust a tension as it is described more low. A coupling bolt and bolts of fastening of the console tighten the moment of 25 Nanometers. |
| 9. Establish a hose of a supply of a liquid with a new collar and the pressure head pipeline. |
| 10. Screw and tighten накидную a nut the moment of 20 Nanometers. |
| 11. After assemblage fill in a liquid in system and remove air as it is described above. |
| 12. Check up system on tightness. |
|
The engine of 2.4 l
This engine is established on cars to the middle of 1995 of release.
| PERFORMANCE ORDER |
| 1. In the presence of the conditioner remove клиновой a belt of a drive of the compressor. |
| 2. Remove клиновой a belt of a drive of the pump of the hydraulic booster as it is described more low. |
| 3. Disconnect from the pump soaking up and pressure head pipelines. |
| 4. Collect a following liquid. Open apertures stop up заглушками. |
| 5. Now it is possible to turn away bolts of fastening and to remove the pump from the console. |
| |
6. Disconnect the pump according to an illustration. For this purpose turn away a coupling bolt and bolts of fastening of the assembly console. |
| 7. If the pump has to be replaced, disconnect a rotary plate and attach it to the new pump. |
| 8. Fastening bolts tighten the moment of 25 Nanometers. |
|
The pump in sequence, by return to removal is established.
| PERFORMANCE ORDER |
| 1. Bolts of fastening of the pump tighten the moment of 25 Nanometers. |
| 2. Observe the instructions resulted above for the pump of the engine of 2.0 l. |
|
The engine of 2.0 l, release from the middle of 1995 and the engine of 2.2 l
Both engines are established on cars of the second generation, i.e. On engines OHC of 2.0 l and DOHC 2.2 l. Keep in mind that on the car with the conditioner the pump is under the generator.
| PERFORMANCE ORDER |
| 1. Ослабьте a belt tension as it is described in the Head the Engine. For both engines. Do not forget to put marks of a direction of rotation of a belt on its external surface. |
| 2. Disconnect from the pump pressure head and soaking up pipelines. |
| 3. A following liquid collect. Open pipelines stop up. |
|
|
4. Turn away bolts 1, 2, 3 and 4, shown on an illustration. |
| 5. Cast away the holder upward and take out the pump. |
|
The pump in sequence, by return to removal is established. Observe following moments of an inhaling:
| PERFORMANCE ORDER |
| 1. Put on клиновой a belt as it is described to the Head the Engine |
| 2. Fill in a liquid in system and remove air (the description in Section 13 see). |
|
REPLACEMENT КЛИНОВОГО OF THE BELT OF THE DRIVE OF THE PUMP OF THE HYDRAULIC BOOSTER
At cars of new generation клиновой the belt acts in film and put on according to the instructions resulted in Section 3 of Chapter 3. It concerns both engine OHC, and to engine DOHC. The following below instructions concerns engines of earlier release.
Engines of 2.0 l to the middle of 1995 of release
It is necessary to remind that in repair trucks to check of a tension of a belt apply the special adaptation. Check of a tension of the belt, described more low, it is necessary to consider time. It is recommended to check up a belt tension in a repair truck later.
| PERFORMANCE ORDER |
|
|
1. Bolts of fastening which are necessary for weakening for a belt tension, are designated on an illustration () and (). At first it is necessary to weaken both bolts () and to turn away bolts () in the bottom part of the pump. |
| 2. Now both nuts on the right and at the left the tension device so that a belt ослаб then he acts in film are regulated. |
| 3. Put on new клиновой a belt and pull its rotation of nuts at the left and to the right of a tension element. The belt stretches so that its deflection under pressing of a finger of a hand between two pulleys made 12 - 13 mm. |
| 4. After adjustment end tighten nuts of the tension device the moment of 25 Nanometers. Other bolts tighten the moment of 25 Nanometers. |
|
Engines of 2.4 l (to the middle of 1995 of release)
| PERFORMANCE ORDER |
|
|
1. At these engines tension bolts клинового a belt are in a place shown on an illustration. |
2. In the presence of the conditioner it is preliminary necessary to remove a belt of a drive of the compressor.
Here too the tension control is carried out by means of the special adaptation. |
|
|
3. Ослабьте tension bolts () and bolts (), shown on an illustration. Ослабьте both nuts in the places shown by arrows so that a belt ослаб also remove it. |
| 4. Put on a new belt and pull its adjustment of the nuts shown by an arrow so that a deflection of a belt under pressing of a finger of a hand between two pulleys made 12 - 13 mm. |
| 5. Tighten adjusting nuts the moment of 40 Nanometers, bolts of fastening of the pump the moment of 25 Nanometers. |
|
|
|
