Opel of Frontera
+ Cars of mark Opel Frontera
+ Current leaving and service
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Coupling
+ Manual box of a gear change
- Kardannye shaft, the main transfer
- Drive of forward wheels
Removal and installation of power shafts of forward wheels
Removal and installation of a nave of a forward wheel
Forward карданный a shaft
+ Drive of back wheels
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Controls and operation
+ Electric equipment schemes
|
Removal and installation of a nave of a forward wheel
For removal of a nave of a wheel the big wrench for отворачивания nuts of fastening of a wheel is required.
| PERFORMANCE ORDER |
|
1. Turn away both bolts of fastening of the support, shown on an illustration. |
| 2. Adhere its wire to the bridge. Do not suspend a support on a hose. |
| 3. Remove блокиратор naves according to the above-stated instructions. |
| 4. Turn out bolts. |
| 5. Remove lock washers. |
|
6. Turn away a nut of fastening of a wheel. The key form is shown on an illustration. |
| 7. Remove a nave together with a brake disk from a rotary fist. |
|
Nave installation is carried out in sequence, return to removal, with following observance:
| PERFORMANCE ORDER |
| 1. Establish a nave and a brake disk on a rotary fist. |
| 2. Screw a nut. |
|
3. A nut tighten the moment of 29 Nanometers by means of a key shown on an illustration, and again completely turn away it. |
|
4. Hook on a dynamometer for a bolt of fastening of a wheel according to an illustration and pull for a dynamometer. |
| 5. The nut of fastening of a wheel is tightened so that the nave with new bearings and new consolidation was turned at traction effort 20 - 24 Н (2.0 - 2.4 kg), and the nave with the bearings which were in the use and new consolidation was turned at traction effort 12 - 17 Н (1.2 - 1.7кг). |
| 6. Establish a lock washer and bolts. |
| 7. If apertures in a washer and apertures in bolts in a nave do not coincide, the washer can be established on the contrary. |
| 8. If and thus it is not reached coincidence, tighten a few nut. |
| 9. Bolts tighten to a washer surface. |
| 10. Establish a support and блокиратор naves. |
| 11. Other works carry out in sequence, return to removal. |
|
REPLACEMENT OF BEARINGS / OF EPIPLOONS OF THE WHEEL
| PERFORMANCE ORDER |
| 1. For replacement of bearings / of epiploons of a wheel it is necessary to remove a wheel nave (see above). |
| 2. Take out from a nave an epiploon, the roller conic bearing and an internal ring. |
| 3. Put a nave on a lining. |
| 4. Выпрессуйте external holders of bearings by means of brass оправки from opposite sides. In a nave there are grooves into which it is possible to insert оправку, that выпрессовать a corresponding holder. |
| 5. Carefully clear a nave and a pin of a rotary fist. |
| 6. Check up the bearing on presence of damages, overheat places, отслоений chrome, etc. And if necessary replace. |
| 7. Запрессуйте in a wheel nave new external holders of bearings by means of corresponding оправки from opposite sides. |
| 8. Fill подшипниковой with greasing both conic roller bearings, epiploons and cavities of a nave of a wheel. Apply the greasing intended for it. |
| 9. Establish separators of bearings. |
| 10. Запрессуйте with the help оправки epiploons so that they were заподлицо with an external surface. |
| 11. Clear a nave of a wheel of available greasing. |
| 12. Establish according to instructions. |
| 13. Establish блокираторы naves depending on their execution as it has been described above. |
|
REPLACEMENT OF THE NAVE OF THE FORWARD WHEEL
At replacement of a nave of a forward wheel it is necessary to observe following instructions:
| PERFORMANCE ORDER |
| 1. If the car is equipped ABS, it is necessary to turn away three bolts and to remove from a nave a gear wreath. |
| 2. At installation bolts tighten the moment of 18 Nanometers. |
| 3. Turn away bolts and remove a brake disk. |
| 4. The disk fastens six bolts. |
| 5. Before disk removal mark its position concerning a wheel nave. |
| 6. At installation bolts tighten the moment of 103 Nanometers. |
| 7. Bolts of fastening of a wheel are necessary for establishing from an old nave on the new. They act in film and established by means of a hammer from soft metal. |
| 8. At installation on a new nave they should occupy former position and strongly sit. |
|
|
|
