Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
- Manual box and differential
   Specifications
   The mechanism of blocking of inclusion of a reverse gear - the device and a functioning principle
   Interaxal differential - the device and a functioning principle
   Removal and installation трансмиссионной assemblages
   Check of a condition and replacement of elements of support of a suspension bracket трансмиссионной assemblages
   Check of a condition and epiploon replacement
   Removal, installation and check of a condition of gauges-switches
   Removal, installation and check of a condition of the gauge of speed (VSS)
   Preparation for performance of major repairs Manual transmission
   Removal, service and installation of a distributing box and transmission lengthening
   Removal, service and installation of a leading gear wheel of the distributing mechanism
   Removal, service and installation of a conducted gear wheel of the distributing mechanism
   Removal, service and installation of interaxal differential
   Removal, service, installation and adjustment of assemblage of the mechanism of blocking of inclusion of a reverse gear
   Removal, installation and condition check картера трансмиссионной assemblages
   Removal, service, installation and adjustment of primary shaft Manual transmission
   Removal, service and installation of entrance shaft Manual transmission (models with an additional two-level reducer)
   Removal, service and installation of assemblage of a shaft of a leading gear wheel of the main transfer of a drive of forward wheels
   Removal, service, installation and adjustment of forward differential
   Removal, installation and check of a condition of a gear wheel of a drive of a speedometer
   Removal, installation and adjustment of an intermediate gear wheel of a reverse gear
   Removal, installation, check and adjustment of assemblage of gear wheels of a two-level reducer
   Removal, check of a condition and installation of plugs and gear change rods
   Removal, service and installation of the lever of gear change Manual transmission
   Removal, service and installation of the lever of switching of modes «Hi/Lo» an additional two-level reducer
   Removal, service and installation тросовой draughts of a drive of switching of modes of a two-level reducer
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


8eee0de7



Check of a condition and replacement of elements of support of a suspension bracket трансмиссионной assemblages

Details of installation of support of a suspension bracket трансмиссионной assemblages are shown on an illustration.

Before removal of elements of support of a suspension bracket трансмиссионной assemblages disconnect a negative wire from the battery.

1 — the Terminator раскачиваний
2 — the Remote plug
3 — Rubber pillow C
4 — the Forward plate
5 — Dempfer of dynamic fluctuations
6 — the Back rubber pillow
7 — the Back cross-section beam
8 — Rubber pillow D
9 — the Central beam
10 — the Back plate
11 — the Forward cross-section beam (model Outback)

12 — the Forward cross-section beam (model Legacy)

Efforts of a tightening of carving connections, Nanometer

Т1: 7.5
Т2: 35
Т3: 50
Т4: 58
Т5: 70
Т6: 140

REMOVAL

The terminator of rocking of the power unit

 PERFORMANCE ORDER

1. Remove an air cleaner
2. Remove the terminator of rocking of the power unit (see Has undressed Removal and installation трансмиссионной assemblages).


Cross-section beam and rubber pillows

 PERFORMANCE ORDER

1. Поддомкратьте the car also establish it on props.
2. Sections of system of release of the fulfilled gases (see the Head of the Power supply system and release).
3. Uncover a thermofilter.
4. Prop up a transmission трансмиссионным a jack (see Has undressed Removal and installation трансмиссионной assemblages).
5. Remove a back cross-section beam.
6. Separate a rubber pillow of a back support of a suspension bracket of the power unit.

CHECK

 PERFORMANCE ORDER

Make sure of absence of deformations of metal components, rubber elements check up on presence of signs of ageing of a material, cracks, cuts and other damages. Make the necessary repair, the failed details replace.

INSTALLATION

 PERFORMANCE ORDER

Installation is made in an order, the return to an order of dismantle of components. Track, that all fixture has been tightened with demanded effort.