Opel of Frontera
+ Cars of mark Opel Frontera
+ Current leaving and service
+ The engine
+ Cooling and heating systems
+ The power supply system and release
+ Engine electric equipment
+ Coupling
- Manual box of a gear change
Transmissionnoe oil
Removal and transmission installation
Transmission repair
+ Kardannye shaft, the main transfer
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Controls and operation
+ Electric equipment schemes
|
Transmission repair
Repair of a transmission demands application of the special tool. Besides, here it would be required to result the description of repair of two transmissions. Experience shows that transmissions work long time without failure. In the presence of any malfunctions address in a repair truck of firm Opel or replace a box.
Some works connected with a transmission which can be executed in the conditions of a house workshop are more low described.
LINING REPLACEMENT BETWEEN CARTER OF THE DISTRIBUTING BOX AND INTERMEDIATE CARTER - TRANSMISSION MSG
At detection of traces of leaks around a joint картера a distributing box and intermediate картера it is necessary to replace a lining.
| PERFORMANCE ORDER |
| 1. Remove the gear change lever as it has been described above. |
| 2. Put the car on supports. |
| 3. Remove forward and back карданные shaft as it will be described in corresponding section. |
| 4. Merge oil from a box. |
| 5. Remove a guard under a distributing box. |
|
6. Remove a back cross-section beam of a suspension bracket of a transmission as it has been described at a transmission. |
| 7. Disconnect a flexible shaft of a drive of a speedometer (till 1997 of release). |
| 8. Расстыкуйте штекерное connection of a speedometer with the electric drive (since 1997 of release). |
| 9. Turn away fastening bolts картера a distributing box with the back party. |
| 10. Take out back картер boxes complete with intermediate картером. |
| 11. Carefully clear the interfaced surfaces intermediate картера and картера a distributing box |
| 12. Connect both картера, having established a new lining. |
| 13. In regular intervals tighten bolts of fastening by the moment of 40 Nanometers. |
| 14. Other works carry out in sequence, return to removal. |
| 15. Establish a cross-beam of a suspension bracket of a transmission. |
| 16. In summary fill in oil in a transmission. |
|
REPLACEMENT OF THE BACK RADIAL EPIPLOON OF CARTER OF THE DISTRIBUTING BOX
| PERFORMANCE ORDER |
| 1. Remove back карданный a shaft as it is described in corresponding section. |
| 2. Cautiously, without having damaged картер, a screw-driver take out an epiploon of transmission MSG. |
| 3. If transmission MUA is established, remove a back flange of a power shaft and take out an epiploon. The flange is necessary for keeping from проворачивания. |
| 4. Grease with impellent oil a working surface of an epiploon |
| 5. Запрессуйте it by means of a pipe in картер transmissions. |
| 6. If it is established transmissions MUA, напрессуйте приводной a flange on a shaft. Tighten a nut the moment of 167 Nanometers. A flange keep from проворачивания. |
| 7. Attach карданный a shaft. |
| 8. In summary check up oil level in a transmission as it has been described in corresponding subsection. |
|
REPLACEMENT OF THE FORWARD RADIAL EPIPLOON OF THE POWER SHAFT OF CARTER OF THE DISTRIBUTING BOX - TRANSMISSION MUA
| PERFORMANCE ORDER |
| 1. Remove forward карданный a shaft. |
| 2. Remove a flange of a forward power shaft, keeping a shaft from проворачивания. |
| 3. Take out a screw-driver an epiploon, watching to damaging картер. |
| 4. Grease with impellent oil a working surface of an epiploon. |
| 5. Запрессуйте it by means of a pipe in картер. |
| 6. Напрессуйте a flange on a shaft. |
| 7. Keeping a shaft from проворачивания, tighten a nut of fastening of a flange the moment of 137 Nanometers. |
| 8. Establish into place forward карданный a shaft. |
| 9. In summary check up oil level in a transmission and, if necessary, add oil. |
|
REPLACEMENT ПРИВОДНОЙ OF THE GEAR WHEEL OF THE SPEEDOMETER
| PERFORMANCE ORDER |
| 1. Disconnect a flexible shaft of a drive of a speedometer. |
| 2. Turn away a bolt of fastening of a gear wheel of a drive of a speedometer |
| 3. Take out the case, linings and приводную a gear wheel from back картера. |
| 4. Establish a new gear wheel with the case and linings. |
| 5. A fastening bolt tighten the moment of 15 Nanometers. |
| 6. Check up oil level in a transmission. |
|
|
|
