Subaru Legacy/Outback

1. Park the car on an equal horizontal platform, whenever possible with a firm covering, develop forward wheels in rectilinear position. Slightly pull a steering wheel in both directions, - the excessive size taking place люфта specifies in possible deterioration of wheel bearings, collars of hinges of shaft of a steering column, bearings of rotary fists, or tips of steering draughts. The probability of infringement of adjustment or damage of components реечной transfers (the Suspension bracket and a steering see the Head) is not excluded also.
2. In deterioration or damage of components of a suspension bracket or a steering drive can specify also such symptoms, as excessive rocking of the car at movement on rough road or during fulfilment of turns, steering wheel jammings, etc.
3. For an estimation of a condition of shock-absorbers press downwards one of car corners. At release a corner the body should come back in a starting position, making no more than one-two fluctuations. Listen to a scratch and the other extraneous noise published by a suspension bracket at oscillative motions of a body. Excessive quantity раскачиваний bodies at release a corner, no less than refusal of its return to a starting position, testify to necessity of replacement of shock-absorbers. Operating in a similar manner, serially check up each of four shock-absorbers.

1. Unload from the car all luggage and leave it completely filled and equipped.
2. Check up height of wheel arches (the Suspension bracket and a steering see the Head), compare results of measurements to requirements of Specifications.
3. If the height of an arch of a wheel does not correspond to specifications, check up a condition of components suspension brackets (racks/shock-absorbers) and bodywork elements to which they fasten. Replace defective components.
4. In the absence of the deformed components adjust height of arches by replacement of corresponding screw springs of a suspension bracket.

1. Check up geometry of a forward suspension bracket and make sure of conformity to the accepted norms of corners of installation of wheels (convergence, disorder, a corner of a longitudinal inclination of an axis of turn of a wheel [выбег], angles of rotation of wheels).
2. If the corner of a longitudinal inclination of an axis of turn of a wheel does not correspond to standard value, visually estimate a condition of components of a suspension bracket (assemblage of forward racks, a cross-section beam, cross-section levers and so forth) and bodywork elements to which they fasten. Replace defective components.
3. If convergence and disorder do not correspond to standard values, make corresponding adjustments (the Suspension bracket and a steering see the Head).
4. If the left and right angles of rotation of wheels do not correspond to standard values, make corresponding adjustments (the Suspension bracket and a steering see the Head).

1. Check up geometry of a forward suspension bracket and make sure of conformity to the accepted norms of corners of installation of wheels (convergence, disorder, a corner of a course deviation).
2. If the disorder corner does not correspond to standard value, visually estimate a condition of components of a suspension bracket (draught [forward, back and top], the back lever, a stretcher, shock-absorbers and so forth) and bodywork elements to which they fasten. Replace defective components.
3. If convergence and a corner of a course deviation do not correspond to standard values, make corresponding adjustments (the Suspension bracket and a steering see the Head).

1. Поддомкратьте the car also establish it on props.
2. Check up protectors of wheels on presence of traces of non-uniform deterioration, estimate pressure of a rating of tyres.

3. Address to materials of the Head the Suspension bracket and a steering. Estimate a condition карданных hinges of a steering column. Check up protective covers of the steering mechanism and power shafts on presence of signs of leaks of greasing. Check up reliability of landing of tips of steering draughts. Check up a condition of all components of a suspension bracket and reliability of a tightening of their fixture. After отдавания самоконтрящихся nuts and bolts, replace their new. Estimate degree of deterioration of rubber components of a suspension bracket and a steering drive. Check up маслозаполненные plugs of levers of a suspension bracket on presence of signs of leaks, in case of need make replacement. Ask the assistant повращать a steering wheel and visually estimate size люфта a steering drive. Try to establish the reason of a taking place weak point, make necessary regenerative repair, or replace defective components.

4. Manually rotating forward wheels, try to define on hearing a condition of wheel bearings, make sure of absence люфта at rotation of wheels. Grasp a wheel in points on 12 and at 6 o'clock and pull it in an axial plane, - presence some an appreciable free wheeling testifies to easing of a pretightness of wheel bearings.
5. Hooking components mount, estimate a condition of bearings of assemblages of rotary fists. In case of revealing люфта it is necessary to subject bearings to more detailed studying, to make replacement or stuffing by their fresh greasing.
6. Estimate degree of deterioration of universal hinges and sliding муфт карданных shaft (Coupling see the Head).
7. Examine surfaces картеров transmissions on presence of signs of development of leaks.

3. At negative results of both checks remove a spherical support (the Suspension bracket and a steering see a disk 2 the Head) and measure size of a free wheeling of a spherical finger (the Suspension bracket and a steering see the Head). Compare result of measurement to requirements of Specifications, in case of need replace spherical support (better in the complete set).

4. Visually estimate a condition dusterа a spherical support. At revealing of mechanical damages, remove the cross-section lever and measure size of a free wheeling of its finger (the Suspension bracket and a steering see the Head). Compare result of measurement to requirements of Specifications, in case of need replace spherical support (better in the complete set).  After removal or replacement of a spherical support it is necessary to check up size of a convergence of forward wheels, - in case of need make corresponding updating.

5. Check of a condition a clod-ponentov steering privo-yes (each 25 000 km [15 000 miles] run or times in 12 months)