Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Search of causes of failures of an electric equipment
   Safety locks - the general information
   Chain breakers - the general information
   The relay - the general information and check of serviceability of functioning
   Details of a lining of onboard electroconducting
   System of additional safety (SRS) - the device and a functioning principle
   Diagnostics of malfunctions SRS
   Removal and installation of components SRS
   Control system of speed (темпостат) - the device and a functioning principle
   Check of serviceability of functioning of components and problem diagnostics темпостата
   Removal, check of a condition and installation of components of a control system by speed
   Combination of devices - the general information and a principle of functioning of components
   Problem diagnostics of components of a combination of devices
   Removal, service and installation of a combination of devices, check of a condition of components
   Heating of back glass and rear-view mirrors - the general information, check of serviceability of functioning of components, regenerative repair of a thermoelectric heating element
   Heating of brushes of screen wipers - the general information, check of serviceability of functioning of components, regenerative repair of a thermoelectric heating element
   Removal, check of a condition and installation of switches of management by functioning of the electric drive of regulators Glass lifts
   The electric drive of rear-view mirrors - check of serviceability of functioning
   Removal check and installation of the switch of management by functioning of the electric drive of external rear-view mirrors
   Removal, check of a condition and installation of the switch of management by functioning of the electric drive of the top hatch
   Removal, check of a condition and installation combined подрулевых switches
   Check of serviceability of functioning of electromotors of a drive of screen wipers, removal, check and installation of the operating relay of a back screen wiper on models Legacy of Universal/Outback
   Check of the relay and switches of lighting and alarm devices
   Removal and installation of lighting devices, replacement of lamps
   Removal, check of a condition and installation of small horns and the horn switch
   Check of a condition and replacement of contact group of the switch of ignition
   The uniform lock - the device, a functioning principle, diagnostics of malfunctions
   Removal, check of a condition and installation of components of the uniform lock
   System иммобилизации the engine - the device, a functioning principle, diagnostics of malfunctions
   Removal and installation of components of system иммобилизации the engine
   Removal and installation of assemblage of a radio receiver
   Removal and installation of loudspeakers
   Check of a condition and regenerative repair of the window aerial of a radio receiver
   Removal, installation and check of a condition of the antenna amplifier of a radio receiver
   Removal and installation прикуривателя
   + Schemes of electric connections


8eee0de7



Removal, check of a condition and installation of components of a control system by speed

Details of installation of panels of furnish of the central console and console section of furnish of the panel of devices

And — the Forward cover of the central console
In — Fixing screws

With — the Central (console) section of furnish of the panel of devices


 Models of cars considered in the present Management are equipped by system of additional safety (SRS). Before to start performance of any works near to the block of a pillow of safety, a steering column or the instrument panel, disconnect SRS in order to avoid reception of traumas at its casual operation (the Section System of additional safety (SRS) - the device and a functioning principle see)! Electroconducting of chain SRS is easy for distinguishing on yellow colour of isolation.

Actuation mechanism with приводным a cable

Removal and installation

 PERFORMANCE ORDER

 Applying to приводному to a cable of excessive effort is fraught with actuation mechanism damage!

1. Disconnect a negative wire from the battery.
2. Release bandage tapes of fastening of a cable of a drive throttle заслонки темпостата.

3. Release a nut of fastening of a tip of a cable to a cam of a drive throttle заслонки.

4. Turn out fixing bolts, disconnect electroconducting and remove actuation mechanism assemblage.

5. Installation is made upside-down, - in summary do not forget to adjust приводной a cable, track correctness of landing of the core of a cable in a flute of a cam and density of landing of a protective cover of a cover of a cable.


Check

 PERFORMANCE ORDER

1. Check of serviceability of a condition of an actuation mechanism is made by resistance measurement between plugs of its contact socket. Compare results of measurements to the data in table 20.

2. In case of reception of negative result of check replace actuation mechanism assemblage.


Tab. 20 the actuation mechanism Scheme темпостата


The management module

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Remove a ware box (the Body see the Head).

3. Give a fixing nut, disconnect electroconducting and remove the management module темпостата complete with the module of management of the uniform lock.

4. Installation is made upside-down.


The main switch

Removal and installation


 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Turn out screws and release clamps of fastening of the bottom section of furnish of the panel of devices.
3. Remove a forward cover of the central console.
4. Turn out fixing screws and remove the central (console) section of furnish of the panel of devices.

5. Turn out fixing screws and liberate from the landing nest in the panel of devices assemblage of a radio receiver and the panel of switches.

6. Disconnect electroconducting and an antenna cable, then remove assemblage of the control panel by functioning of a heater/conditioner of air.

7. Turn out fixing screws, separate an arm and remove the panel of switches.

8. Disconnect electroconducting and push out the main switch темпостата from assemblage of the panel of switches.

9. Installation is made upside-down.


Check

 PERFORMANCE ORDER

1. Check of serviceability of a condition of the main switch is made by resistance measurement between plugs of its contact socket in both working positions («ON» and «OFF»). Compare results of measurements to the data in table 21.

2. In case of reception of negative result of check replace the switch.


Tab. 21 the Scheme of the main switch темпостата


The combined operating switch

 Models of cars considered in the present Management are equipped by system of additional safety (SRS). Before to start performance of any works near to the block of a pillow of safety, a steering column or the instrument panel, disconnect SRS in order to avoid reception of traumas at its casual operation (the Section System of additional safety (SRS) - the device and a functioning principle see)! Electroconducting of chain SRS is easy for distinguishing on yellow colour of isolation.


Removal and installation

 PERFORMANCE ORDER

1. The combined operating switch is fixed on a car steering wheel.
2. Result lobbies коелса the car in rectilinear position.
3. Make switching-off SRS (the Section System of additional safety (SRS) - the device and a functioning principle see).
4. Turn out lateral screws of fastening of the module of a driver's face-to-face pillow of safety.
5. Disunite a contact socket of electroconducting SRS from the back party of the module of a pillow of safety.

6. Remove from a steering wheel the horn switch.

7. Disconnect electroconducting and remove the combined operating switch темпостата.

8. Installation is made upside-down.


Check

 PERFORMANCE ORDER

1. Check of serviceability of a condition of the operating switch is made by resistance measurement between plugs of its contact socket in all working positions. Compare results of measurements to the data in table 22.

2. In case of reception of negative result of check replace the switch.


Tab. 22 the Scheme of the operating switch темпостата


Assemblage of gauges-switches of stops-signals/braking

Removal and installation

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Disconnect electroconducting and remove assemblage of gauges-switches (the Brake system see the Head).
3. Installation is made upside-down.


Check

 PERFORMANCE ORDER

1. Check of serviceability of a condition of assemblage of gauges-switches is made by resistance measurement between plugs of its contact socket in all working positions. Compare results of measurements to the data in table 23.

2. In case of reception of negative result of check replace assemblage of gauges-switches.


Tab. 23 the Scheme of assemblage of gauges-switches of stops-signals/braking


The coupling gauge-switch (models with Manual transmission)

Removal and installation


 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Disconnect electroconducting and remove the gauge-switch (Coupling see the Head).
3. Installation is made upside-down.


Check

 PERFORMANCE ORDER

1. Check of serviceability of a condition of the gauge-switch is made by resistance measurement between plugs of its contact socket in its both positions. Compare results of measurements to the data in table 24.

2. In case of reception of negative result of check replace the gauge-switch.


Tab. 24 the Scheme of the gauge-switch of coupling (model with Manual transmission)


The gauge-switch razre-shenija start (model with АТ)

Removal and installation


 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Disconnect electroconducting and remove the gauge-switch.
3. Installation is made upside-down.


Check

 PERFORMANCE ORDER

1. Check of serviceability of a condition of gauge-switch R/N is made by resistance measurement between plugs of its contact socket in various positions of the lever of selector AT. Compare results of measurements to the data in table 25.

2. In case of reception of negative result of check replace the gauge-switch.


Tab. 25 gauge-switch R/N Scheme (models with АТ)