Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
Specifications
Brake mechanisms of forward and back wheels - the general information
Lay brake - a design and a functioning principle
The pressure valve-terminator - a design and a functioning principle
Protivootkatnaja system - the device, a functioning and safety measure principle
System of antiblocking of brakes (ABS) - the general information, a functioning principle
System of dynamic stabilisation (VDC) - the general information, a functioning principle
Check of a condition replacement колодок disk brake mechanisms of forward wheels
Removal, check of a condition and installation of forward brake disks
Removal, service and installation of disk brake mechanisms of forward wheels
Check of a condition and replacement колодок disk brake mechanisms of back wheels
Removal, check of a condition and installation of back brake disks
Removal, service and installation of disk brake mechanisms of back wheels
Removal, service and installation of the main brake cylinder (ГТЦ)
Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
Removal, installation and check of serviceability of functioning of the valve-terminator of pressure
Replacement of a brake liquid
Prorolling of a hydraulic path of brake system
Check of a condition and replacement of flexible brake hoses
Check of a condition and replacement of tubes of a brake path
Removal, service, installation and adjustment of a pedal of a foot brake
Removal, condition check, installation and adjustment of the gauge-switch of stoplights
Removal, installation, check of a condition and adjustment of the lever of a drive of a lay brake
Removal, check of a condition and installation of elements тросового a drive of a lay brake
Removal, installation and adjustment of the mechanism of a lay brake
Removal, installation, check of a condition and adjustment of components противооткатного devices
Removal, installation and check of serviceability of functioning of assemblage of the module of management/hydromodulator ABS
Check of sequence of operation of valves of hydromodulator ABS
Removal, installation and check of serviceability of functioning of forward wheel gauges ABS
Removal, installation and check of serviceability of functioning of back wheel gauges ABS
Removal, installation and check of a condition of rotors of wheel gauges
Removal, installation and diagnostics of the gauge of overloads (G-gauge)
Problem diagnostics ABS
Removal, installation and adjustment of the module of management VDC
Removal, installation and check of serviceability of functioning of hydromodulator VDC
Check of sequence of operation of valves of hydromodulators ABS and VDC
Removal, installation and check of serviceability of functioning of the gauge of withdrawal / cross-section overloads
Removal, installation and check of serviceability of functioning of the gauge of an angle of rotation of steering wheel VDC
Removal, installation and check of serviceability of functioning of wheel gauges from rotors
Removal, installation and check of serviceability of functioning of the switch of deactivation VDC (VDC OFF)
Problem diagnostics VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Check of a condition replacement колодок disk brake mechanisms of forward wheels
REMOVAL
|
|
1. Release wheel nuts, поддомкратьте redock of the car and establish it on props, remove a corresponding wheel.
2. Turn out the bottom directing bolt, lift the case of a support and tie up it in the lifted position. The remark: Necessity for a detachment of a flexible brake hose is absent.
|
|
3. Take Pads from анкерной скобы. |
|
|
4. If Pads "have become attached" and do not give in to extraction, remove анкерную скобу and clamp it in a vice with soft sponges, then hammer blows on выколотке in diameter less than 12 mm, a surface rested against shaded sites Pads, liberate last from the landing nest in скобе. |
|
|
CHECK
|
|
|
|
Колодки it is necessary to change in the complete set for both brake mechanisms of one axis of the car! |
Measure a residual thickness of a frictional overlay (taking into account a metal substrate Pads). Compare result of measurement to requirements of Specifications, in case of need replace Pads.
|
|
Replacement is made also in a case замасливания колодок or выступания the deterioration indicator on internal колодке for limits of a frictional overlay (the indicator starts to rub about a surface of a brake disk, publishing a characteristic high-frequency sound). |
|
|
INSTALLATION
|
|
|
|
1. Before installation interfaced to clamps and internal adjusting linings of a surface колодок it is necessary to grease with greasing Molykote AS880N (№ 26298АС000).
|
|
Try not to admit greasing hit on a surface of frictional overlays and a working surface of a brake disk! |
|
2. Estimate also a condition and size of lateral palpation of a brake disk (see Has undressed Removal, check of a condition and installation of forward brake disks).
3. Establish Pads in landing nests анкерной скобы. Lower a support, - in case of need ослабьте the gate of prorolling of a support for the purpose of simplification of landing of the last. The effort of a tightening of a directing bolt makes 39 Nanometers.
4. Some times squeeze out a pedal of a foot brake, check up level of a hydraulic liquid in tank GTTS (Routine maintenance see the Head). |
|
|
|
