Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
Specifications
Brake mechanisms of forward and back wheels - the general information
Lay brake - a design and a functioning principle
The pressure valve-terminator - a design and a functioning principle
Protivootkatnaja system - the device, a functioning and safety measure principle
System of antiblocking of brakes (ABS) - the general information, a functioning principle
System of dynamic stabilisation (VDC) - the general information, a functioning principle
Check of a condition replacement колодок disk brake mechanisms of forward wheels
Removal, check of a condition and installation of forward brake disks
Removal, service and installation of disk brake mechanisms of forward wheels
Check of a condition and replacement колодок disk brake mechanisms of back wheels
Removal, check of a condition and installation of back brake disks
Removal, service and installation of disk brake mechanisms of back wheels
Removal, service and installation of the main brake cylinder (ГТЦ)
Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
Removal, installation and check of serviceability of functioning of the valve-terminator of pressure
Replacement of a brake liquid
Prorolling of a hydraulic path of brake system
Check of a condition and replacement of flexible brake hoses
Check of a condition and replacement of tubes of a brake path
Removal, service, installation and adjustment of a pedal of a foot brake
Removal, condition check, installation and adjustment of the gauge-switch of stoplights
Removal, installation, check of a condition and adjustment of the lever of a drive of a lay brake
Removal, check of a condition and installation of elements тросового a drive of a lay brake
Removal, installation and adjustment of the mechanism of a lay brake
Removal, installation, check of a condition and adjustment of components противооткатного devices
Removal, installation and check of serviceability of functioning of assemblage of the module of management/hydromodulator ABS
Check of sequence of operation of valves of hydromodulator ABS
Removal, installation and check of serviceability of functioning of forward wheel gauges ABS
Removal, installation and check of serviceability of functioning of back wheel gauges ABS
Removal, installation and check of a condition of rotors of wheel gauges
Removal, installation and diagnostics of the gauge of overloads (G-gauge)
Problem diagnostics ABS
Removal, installation and adjustment of the module of management VDC
Removal, installation and check of serviceability of functioning of hydromodulator VDC
Check of sequence of operation of valves of hydromodulators ABS and VDC
Removal, installation and check of serviceability of functioning of the gauge of withdrawal / cross-section overloads
Removal, installation and check of serviceability of functioning of the gauge of an angle of rotation of steering wheel VDC
Removal, installation and check of serviceability of functioning of wheel gauges from rotors
Removal, installation and check of serviceability of functioning of the switch of deactivation VDC (VDC OFF)
Problem diagnostics VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal, installation and check of serviceability of functioning of the gauge of an angle of rotation of steering wheel VDC
Details of installation of the gauge of an angle of rotation of steering wheel VDC
REMOVAL
|
|
| 1. Disconnect a negative wire from the battery.
2. Remove the module of a driver's face-to-face pillow of safety (the Onboard electric equipment see the Head).
|
|
3. Result forward wheels of the car in rectilinear position, give a fixing nut and remove a steering wheel from a shaft of a steering column, - take advantage of a stripper.
1 — the Stripper |
|
|
4. Turn out the screw of fastening of the bottom cover of a casing of a steering column. |
|
|
5. Turn out two fastenings of the top cover of a casing of a column, release a clamp of a plait of electroconducting and disunite a socket of the gauge of an angle of rotation of a steering wheel.
1 — the Plait
2 — the Contact socket |
6. Turn out fixing screws and remove assemblage of a contact drum with the gauge of an angle of rotation of a steering wheel.
|
|
INSTALLATION
|
|
|
1. Make sure that forward wheels are in rectilinear position.
|
|
2. Plant gauge assemblage on a steering column. |
3. Centre (the Onboard electric equipment) see the Head and plant on the regular place a contact drum.
4. Screw and tighten 7 screws of fastening of a contact drum/gauge of an angle of rotation of a steering wheel.
5. Plant on the regular place a steering wheel, centre it and fix a nut, having tightened last with demanded effort (44 Nanometers). In order to avoid damages track, that the directing finger of a contact drum has got to a reciprocal aperture in ступичной steering wheel parts, at once liberate contact sockets of electroconducting of a pillow of safety, a horn and темпостата, having passed them in directing aperture in a steering wheel.
6. The further installation is made in an order, the return to an order of dismantle of components. Track, that the backlash between a landing surface of a steering wheel and face surfaces of covers did not fall outside the limits an admissible range (2 ÷ 4 mm).
7. Establish into place the module of a pillow of safety (the Onboard electric equipment see the Head), then connect a negative wire to the battery.
8. In summary it is necessary to make installation of the central position of the gauge of an angle of rotation of a steering wheel and zeroing of the gauge of withdrawal / cross-section overloads (see Has undressed Removal, installation and adjustment of the module of management VDC). |
|
Check of serviceability of functioning of the gauge
|
|
