Subaru Legacy/Outback

1999-2003 of release

Repair and car operation



Subaru Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ The operation manual
+ Routine maintenance
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
   Specifications
   Brake mechanisms of forward and back wheels - the general information
   Lay brake - a design and a functioning principle
   The pressure valve-terminator - a design and a functioning principle
   Protivootkatnaja system - the device, a functioning and safety measure principle
   System of antiblocking of brakes (ABS) - the general information, a functioning principle
   System of dynamic stabilisation (VDC) - the general information, a functioning principle
   Check of a condition replacement колодок disk brake mechanisms of forward wheels
   Removal, check of a condition and installation of forward brake disks
   Removal, service and installation of disk brake mechanisms of forward wheels
   Check of a condition and replacement колодок disk brake mechanisms of back wheels
   Removal, check of a condition and installation of back brake disks
   Removal, service and installation of disk brake mechanisms of back wheels
   Removal, service and installation of the main brake cylinder (ГТЦ)
   Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
   Removal, installation and check of serviceability of functioning of the valve-terminator of pressure
   Replacement of a brake liquid
   Prorolling of a hydraulic path of brake system
   Check of a condition and replacement of flexible brake hoses
   Check of a condition and replacement of tubes of a brake path
   Removal, service, installation and adjustment of a pedal of a foot brake
   Removal, condition check, installation and adjustment of the gauge-switch of stoplights
   Removal, installation, check of a condition and adjustment of the lever of a drive of a lay brake
   Removal, check of a condition and installation of elements тросового a drive of a lay brake
   Removal, installation and adjustment of the mechanism of a lay brake
   Removal, installation, check of a condition and adjustment of components противооткатного devices
   Removal, installation and check of serviceability of functioning of assemblage of the module of management/hydromodulator ABS
   Check of sequence of operation of valves of hydromodulator ABS
   Removal, installation and check of serviceability of functioning of forward wheel gauges ABS
   Removal, installation and check of serviceability of functioning of back wheel gauges ABS
   Removal, installation and check of a condition of rotors of wheel gauges
   Removal, installation and diagnostics of the gauge of overloads (G-gauge)
   Problem diagnostics ABS
   Removal, installation and adjustment of the module of management VDC
   Removal, installation and check of serviceability of functioning of hydromodulator VDC
   Check of sequence of operation of valves of hydromodulators ABS and VDC
   Removal, installation and check of serviceability of functioning of the gauge of withdrawal / cross-section overloads
   Removal, installation and check of serviceability of functioning of the gauge of an angle of rotation of steering wheel VDC
   Removal, installation and check of serviceability of functioning of wheel gauges from rotors
   Removal, installation and check of serviceability of functioning of the switch of deactivation VDC (VDC OFF)
   Problem diagnostics VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


8eee0de7



Check of sequence of operation of valves of hydromodulator ABS

The scheme of connection of diagnostic plugs at check of sequence of operation of valves of hydromodulator ABS

1 — the Diagnostic socket
2 — Diagnostic plugs

3 — the Plug № 8
4 — the Plug № 5


Card of diagnostics of serviceability of functioning of the hydromodulator

 


 The Section Problem diagnostics ABS see also.


Check without application SSM

 PERFORMANCE ORDER

1. Connect diagnostic plugs to plugs №№ 5 and 8 heaters of a driver's seat of a diagnostic socket close by the block.
2. Include transfer and achieve rotation of wheels of the car with the frequency corresponding to speed of movement below 2.75 km/h, then switch off ignition.
3. Again turn the ignition key in position ON (the engine do not start) and within 0.5 seconds after switching-off of control lamp ABS, squeeze out and keep pressed a pedal of a foot brake.

 Pedal of coupling do not squeeze out!

4. After check end switch off ignition.


Check with application SSM

 PERFORMANCE ORDER

If performance of check with application SSM is not obviously possible owing to any infringement, operate, as it is described in paragraphs with 1 on 4.


 At the diagnostic plugs connected to a diagnostic socket check performance is not obviously possible!

1. Connect SSM to located at the left under the panel of devices to socket DLC of the car.
2. Include ignition, then include food SSM.
3. Translate SSM in a mode of check of brake system {BRAKE CONTROL},
4. Activation of check of sequence of operation ABS occurs at a choice of subsection of the menu {Function check sequence}.
5. At occurrence on the screen of the display of the message «Firmly squeeze out a pedal of a foot brake» (Press Brake Pedal Firmly), it is necessary to squeeze out a pedal with effort 100 кГс (at check performance at the stand)/35 кГс (at check with application of measuring instruments (see Has undressed Removal, installation and check of serviceability of functioning of assemblage of the module of management/hydromodulator ABS).

 Pedal of coupling do not squeeze out! Message occurrence «Press YES» means that it is necessary to press button YES. The check course will be reflected in the monitor screen.


Exit from a check mode

 PERFORMANCE ORDER

The exit from a mode of check in a mode of normal functioning occurs to transition ABS in following cases:

a) At increase in frequency of rotation of any of wheels to the size corresponding to speed of movement more 10 km/h;
b) At a detachment of diagnostic plugs from plugs №№ 5 and 8 diagnostic sockets (without application SSM);
c) At release pedals foot brake/disconnection of the gauge-switch of stoplights;
d) At lateness of squeezing of a pedal of a foot brake after inclusion of ignition and switching-off of control lamp ABS (without application SSM);
e) At delay of squeezing of a pedal of a foot brake more than for 0.5 seconds after switching-off of control lamp ABS (without application SSM);
f) On termination of a verifying cycle.